View SM500606_4127532.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SM5006 series Crystal Oscillator Module ICs
OVERVIEW
The SM5006 series are crystal oscillator module ICs, that incorporate high-frequency, low current consumption oscillator and output buffer circuits. Highly accurate thin-film feedback resistors and high-frequency capacitors are built-in, eliminating the need for external components to make a stable 3rd overtone oscillator.
FEATURES
I I I I I I
Up to 107MHz operation Capacitors CG, CD built-in Inverter amplifier feedback resistor built-in TTL input level 16mA (VDD = 4.5V) drive capability 4mA (VDD = 4.5V) drive capability (5006AHx)
I I I I I
Output three-state function 2.7 to 5.5V supply voltage Oscillator frequency output 8-pin SOP (SM5006xxxS) Chip form (CF5006xxx)
SERIES CONFIGURATION
3V operating Version*1 gm ratio Output load (max) [pF] - - 15 15 15 - 15 15 15 15 15 15 15 - - - - - - - - - - - Recommended operating frequency range*2 [MHz] - - 22 to 30 30 to 50 50 to 70 - 22 to 30 30 to 40 50 to 70 22 to 70 22 to 70 22 to 40 22 to 70 - - - - - - - - - - - Output load (max) [pF] 50 50 50 50 30 (15)*4 30 (15)*4 15 50 15 15 15 50 30 (15)*4 15 50 15 50 15 15 15 15 15 15 15 15 15 15 15 5V operating Recommended operating frequency range*2 [MHz] 22 to 30 30 to 40 40 to 60 50 to 70 70 to 100 80 to 107 40 to 60 40 to 50 50 to 70 70 to 100 22 to 100 22 to 70 70 to 107 22 to 70 22 to 50 22 to 100 22 to 70 22 to 30 30 to 40 40 to 60 50 to 70 50 to 70 22 to 70 22 to 70 22 to 30 30 to 40 40 to 60 50 to 70 Output waveform*3 tr /tf [ns] 8/8 8/8 7/7 7/7 6/6 6/6 8/8 8/8 7/7 7/7 6/6 8/8 7/7 4/4 4/4 4/4 4/4 4/4 4/4 4/4 7/7 7/7 7/7 7/7 Built-in capacitance CG [pF] 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 CD [pF] 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 Rf [k] 8.2 5.6 4.9 2.6 2.6 2.6 4.9 2.6 2.6 No No No No 8.2 5.6 4.9 2.6 2.6 No No 8.2 5.6 4.9 2.6 Input level Output duty level CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS TTL TTL TTL TTL TTL TTL TTL CMOS CMOS CMOS CMOS
SM5006ANAS SM5006ANBS SM5006ANCS SM5006ANDS SM5006ANES SM5006ANFS SM5006CNCS SM5006CNDS SM5006CNES SM5006BNCS SM5006BNES SM5006DNCS SM5006DNES SM5006AKAS SM5006AKBS SM5006AKCS SM5006AKDS SM5006CKDS SM5006BKCS SM5006DKCS SM5006AHAS SM5006AHBS SM5006AHCS SM5006AHDS
0.5 1 2 2 3 4 2 2 3 2 3 2 3 0.5 1 2 2 2 2 2 0.5 1 2 2
TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL
*1. Chip form devices have designation CF5006xxx. *2. The recommended operating frequency is a yardstick value derived from the crystal used for NPC characteristics authentication. However, the oscillator frequency band is not guaranteed. Specifically, the characteristics can vary greatly due to crystal characteristics and mounting conditions, so the oscillation characteristics of components must be carefully evaluated. *3. 5006xNx: CL = 50pF, CMOS load, 5006xKx: CL = 15pF, 10TTL load, 5006AHx: CL = 15pF, CMOS load *4. SOP package only SEIKO NPC CORPORATION --1
SM5006 series
ORDERING INFORMATION
Device SM5006xxxS CF5006xxx-1 Package 8-pin SOP Chip form
PACKAGE DIMENSIONS
(Unit: mm) * 8-pin SOP
0.15 + 0.1 - 0.05
4.4 0.2
6.2 0.3
0.695typ 5.2 0.3
0.05 0.05
1.5
0.1
1.27
0.4 0.2
0.10 0.4 0.1 0.12 M
0 to 10
SEIKO NPC CORPORATION --2
SM5006 series
PAD LAYOUT
(Unit: m)
PINOUT
(Top view)
VDD
Q
(920,1310)
Y
(0,0) INHN XT XTN VSS X
Chip size: 0.92 x 1.31mm Chip thickness: 300 30m Chip base: VDD level
PIN DESCRIPTION and PAD DIMENSIONS
Number 1 2 3 4 5 6 7 8 Name INHN XT XTN VSS Q NC NC VDD I/O I I O - O - - - Description Output state control input. High impedance when LOW. Pull-up resistor built in Amplifier input. Amplifier output. Ground Output. Output frequency (fO) No connection No connection Supply voltage Crystal oscillator connection pins. Crystal oscillator connected between XT and XTN Pad dimensions [m] X 195 385 575 766 765 - - 162 Y 212 212 212 212 1152 - - 1152
BLOCK DIAGRAM
VDD VSS XTN
RG CG Rf RD CD
XT
INHN
HA5006
INHN XT XTN VSS
1 2 3 4
8 7 6 5
VDD NC NC Q
Q
SEIKO NPC CORPORATION --3
SM5006 series
SPECIFICATIONS
Absolute Maximum Ratings
VSS = 0V
Parameter Supply voltage range Input voltage range Output voltage range Operating temperature range Storage temperature range Symbol VDD VIN VOUT Topr Chip form Tstg 8-pin SOP 5006xNx, xKx 5006AHx 8-pin SOP Condition Rating -0.5 to 7.0 -0.5 to VDD + 0.5 -0.5 to VDD + 0.5 -40 to 85 -65 to 150 -55 to 125 25 mA 10 500 mW Unit V V V C C
Output current Power dissipation
IOUT PD
SEIKO NPC CORPORATION --4
SM5006 series
Recommended Operating Conditions
SM5006 series (package form) VSS = 0V
Rating Parameter Symbol Series Condition min f 50MHz, CL = 50pF ANA, ANB, CNC, CND, DNC f 70MHz, CL = 15pF f 40MHz, CL = 15pF f 70MHz, CL = 50pF ANC, AND, BNC, CNE, DNE f 100MHz, CL = 15pF f 50MHz, CL = 15pF f 70MHz, CL = 15pF Supply voltage VDD ANE, ANF, BNE f 100MHz, CL = 15pF f 107MHz, CL = 15pF f 50MHz, CL = 15pF f 70MHz, CL = 15pF AKA, AKB, AKC, CKD, DKC AKD, BKC AHA, AHB, AHC, AHD Input voltage VIN All series f 50MHz, CL = 50pF, 4.5 VDD 5.5 ANA, ANB, CNC, CND, DNC f 70MHz, CL = 15pF, 4.5 VDD 5.5 f 40MHz, CL = 15pF, 2.7 VDD 3.6 f 50MHz, CL = 50pF, 4.5 VDD 5.5 f 70MHz, CL = 50pF, 4.5 VDD 5.5 ANC, AND, BNC, CNE, DNE f 70MHz, CL = 15pF, 4.5 VDD 5.5 f 100MHz, CL = 15pF, 4.5 VDD 5.5 f 50MHz, CL = 15pF, 2.7 VDD 3.6 f 70MHz, CL = 15pF, 3.0 VDD 3.6 Operating temperature TOPR ANE, ANF, BNE f 70MHz, CL = 50pF, 4.5 VDD 5.5 f 100MHz, CL = 15pF, 4.5 VDD 5.5 f 107MHz, CL = 15pF, 4.5 VDD 5.5 f 50MHz, CL = 15pF, 2.7 VDD 3.6 f 70MHz, CL = 15pF, 3.0 VDD 3.6 AKA, AKB, AKC, CKD, DKC AKD, BKC AHA, AHB, AHC, AHD f 50MHz, CL = 15pF, 4.5 VDD 5.5 f 70MHz, CL = 15pF, 4.5 VDD 5.5 f 50MHz, CL = 15pF, 4.5 VDD 5.5 f 70MHz, CL = 15pF, 4.5 VDD 5.5 f 50MHz, CL = 15pF, 4.5 VDD 5.5 f 70MHz, CL = 15pF, 4.5 VDD 5.5 f 70MHz, CL = 15pF f 70MHz, CL = 15pF f 70MHz, CL = 15pF 4.5 4.5 2.7 4.5 4.5 2.7 3.0 4.5 4.5 2.7 3.0 4.5 4.5 4.5 VSS - 40 0 - 10 - 40 - 20 - 40 0 - 20 - 20 - 20 - 40 - 20 - 20 - 20 - 40 0 - 40 - 20 - 40 - 15 typ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - max 5.5 5.5 3.6 5.5 5.5 V 3.6 3.6 5.5 5.5 V 3.6 3.6 5.5 5.5 5.5 VDD + 85 + 70 + 70 + 80 + 80 + 85 + 70 + 80 + 80 + 80 + 85 + 80 + 80 + 80 + 85 + 70 + 85 + 80 + 85 + 75 C C C C V V V V V Unit
C
C
SEIKO NPC CORPORATION --5
SM5006 series CF5006 series (chip form) VSS = 0V
Rating Parameter Symbol Series Condition min f 50MHz, CL = 50pF ANA, ANB, CNC, CND, DNC f 70MHz, CL = 15pF f 40MHz, CL = 15pF f 70MHz, CL = 50pF ANC, AND, BNC, CNE, DNE f 100MHz, CL = 15pF f 50MHz, CL = 15pF f 70MHz, CL = 15pF Supply voltage VDD ANE, ANF, BNE f 70MHz, CL = 50pF f 107MHz, CL = 30pF f 50MHz, CL = 15pF f 70MHz, CL = 15pF AKA, AKB, AKC, CKD, DKC AKD, BKC AHA, AHB, AHC, AHD Input voltage VIN All series f 50MHz, CL = 50pF, 4.5 VDD 5.5 ANA, ANB, CNC, CND, DNC f 70MHz, CL = 15pF, 4.5 VDD 5.5 f 40MHz, CL = 15pF, 2.7 VDD 3.6 f 70MHz, CL = 50pF, 4.5 VDD 5.5 ANC, AND, BNC, CNE, DNE f 100MHz, CL = 15pF, 4.5 VDD 5.5 f 50MHz, CL = 15pF, 2.7 VDD 3.6 f 70MHz, CL = 15pF, 3.0 VDD 3.6 f 70MHz, CL = 50pF, 4.5 VDD 5.5 Operating temperature TOPR f 100MHz, CL = 30pF, 4.5 VDD 5.5 ANE, ANF, BNE f 107MHz, CL = 30pF, 4.5 VDD 5.5 f 50MHz, CL = 15pF, 2.7 VDD 3.6 f 70MHz, CL = 15pF, 3.0 VDD 3.6 AKA, AKB, AKC, CKD, DKC AKD, BKC AHA, AHB, AHC, AHD f 50MHz, CL = 15pF, 4.5 VDD 5.5 f 70MHz, CL = 15pF, 4.5 VDD 5.5 f 50MHz, CL = 15pF, 4.5 VDD 5.5 f 70MHz, CL = 15pF, 4.5 VDD 5.5 f 50MHz, CL = 15pF, 4.5 VDD 5.5 f 70MHz, CL = 15pF, 4.5 VDD 5.5 f 70MHz, CL = 15pF f 70MHz, CL = 15pF f 70MHz, CL = 15pF 4.5 4.5 2.7 4.5 4.5 2.7 3.0 4.5 4.5 2.7 3.0 4.5 4.5 4.5 VSS - 40 - 15 - 10 - 40 - 20 - 20 - 20 - 40 - 40 - 20 - 20 - 20 - 40 - 15 - 40 - 20 - 40 - 20 typ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - max 5.5 5.5 3.6 5.5 5.5 V 3.6 3.6 5.5 5.5 V 3.6 3.6 5.5 5.5 5.5 VDD + 85 + 75 + 70 + 85 + 80 + 80 + 80 + 85 + 85 + 80 + 80 + 80 + 85 + 75 + 85 + 80 + 85 + 80 C C C C V V V V V Unit
C
C
SEIKO NPC CORPORATION --6
SM5006 series
Electrical Characteristics
5006xN series 3V operation: VDD = 2.7 to 3.6 V, VSS = 0 V, Ta = -20 to 80 C unless otherwise noted.
Rating Parameter HIGH-level output voltage LOW-level output voltage Output leakage current HIGH-level input voltage LOW-level input voltage Symbol VOH VOL IZ VIH VIL Condition min Q: Measurement cct 1, VDD = 2.7V, IOH = 8mA Q: Measurement cct 2, VDD = 2.7V, IOL = 8mA Q: Measurement cct 2, INHN = LOW, VDD = 5.5V INHN INHN SM5006ANCS CF5006ANC SM5006BNCS CF5006BNC SM5006CNCS CF5006CNC SM5006ANDS CF5006AND SM5006BNES CF5006BNE SM5006CNES CF5006CNE SM5006DNES CF5006DNE SM5006CNDS CF5006CND SM5006DNCS CF5006DNC SM5006ANES CF5006ANE SM5006ANFS CF5006ANF VOH = VDD VOL = VSS 2.2 - - - 2.0 - typ 2.4 0.3 - - - - max - 0.4 10 A 10 - 0.5 V V V V Unit
f = 30MHz
-
8
16
f = 30MHz, Ta = -10 to 70C f = 50MHz INHN = open, Measurement cct 3, load cct 1, VDD = 3.0 to 3.6V, CL = 15pF
- -
8 13
16 26
Current consumption
IDD
f = 70MHz
-
15
30
mA
f = 40MHz, Ta = -10 to 70C
-
11
22
f = 70MHz
-
20
40
INHN pull-up resistance
RUP
Measurement cct 4 SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006ANCS, CF5006ANC SM5006CNCS, CF5006CNC SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006CNDS, CF5006CND SM5006CNES, CF5006CNE
50 6.97 4.76 4.16
- 8.2 5.6 4.9
150 9.43 6.44 5.64
k
Feedback resistance
Rf
Measurement cct 5
k
2.21
2.6
2.99
Built-in resistance
RG RD
Design value, determined by the Rf value Design value, determined by the Rf value Design value. A monitor pattern on a wafer is tested. Design value. A monitor pattern on a wafer is tested.
17 17 7.44 14.88
20 20 8 16
23 23 8.56
Built-in capacitance
CG CD
pF 17.12
SEIKO NPC CORPORATION --7
SM5006 series 5V operation: VDD = 4.5 to 5.5V, VSS = 0V, Ta = -40 to 85C unless otherwise noted.
Parameter HIGH-level output voltage LOW-level output voltage Output leakage current HIGH-level input voltage LOW-level input voltage Symbol VOH VOL IZ VIH VIL Condition Q: Measurement cct 1, VDD = 4.5V, IOH = 16mA Q: Measurement cct 2, VDD = 4.5V, IOL = 16mA Q: Measurement cct 2, INHN = LOW, VDD = 5.5V INHN INHN f = 30MHz f = 40MHz INHN = open, Measurement cct 3, load cct 1, VDD = 4.5 to 5.5V, CL = 50pF f = 60MHz f = 60MHz, Ta = -20 to 80C f = 70MHz f = 70MHz, Ta = -20 to 80C f = 60MHz, CL = 15pF, Ta = -15 to 75C Current consumption IDD f = 60MHz, CL = 15pF, Ta = 0 to 70C f = 70MHz, CL = 15pF, Ta = -15 to 75C f = 70MHz, CL = 15pF, Ta = 0 to 70C f = 100MHz, CL = 15pF, Ta = -20 to 80C f = 100MHz, CL = 15pF, Ta = 0 to 70C f = 100MHz, CL = 30pF f = 100MHz, CL = 15pF f = 107MHz, CL = 30pF, Ta = -20 to 80 C f = 107MHz, CL = 15pF, Ta = -20 to 80C INHN pull-up resistance RUP Measurement cct 4 SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006ANCS, CF5006ANC SM5006CNCS, CF5006CNC SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006CNDS, CF5006CND SM5006CNES, CF5006CNE Design value, determined by the Rf value Design value, determined by the Rf value Design value. A monitor pattern on a wafer is tested. Design value. A monitor pattern on a wafer is tested. SM5006ANAS CF5006ANA SM5006ANBS CF5006ANB CF5006ANC SM5006ANCS CF5006AND CF5006BNC SM5006ANDS SM5006BNCS CF5006CNC SM5006CNCS CF5006CND CF5006DNC SM5006CNDS SM5006DNCS CF5006CNE CF5006DNE SM5006CNES SM5006DNES CF5006ANE SM5006ANES CF5006ANF CF5006BNE SM5006ANFS SM5006BNES VOH = VDD VOL = VSS Rating min 4.0 - - - 2.0 - - - - - - - - - - - - - - - - - 50 6.97 4.76 4.16 typ 4.2 0.3 - - - - 18 20 30 30 40 40 28 28 35 35 45 45 50 45 60 50 - 8.2 5.6 4.9 max - 0.4 10 10 - 0.8 35 40 60 50 80 70 50 50 65 65 80 80 100 90 100 90 150 9.43 6.44 5.64 k 2.21 2.6 2.99 k Unit V V A V V
mA
INHN = open, Measurement cct 3, load cct 1, VDD = 4.5 to 5.5V
Feedback resistance
Rf
Measurement cct 5
Built-in resistance
RG RD CG CD
17 17 7.44 14.88
20 20 8 16
23 23 8.56 17.12
pF
Built-in capacitance
SEIKO NPC CORPORATION --8
SM5006 series 5006xK series VDD = 4.5 to 5.5V, VSS = 0V, Ta = -40 to 85C unless otherwise noted.
Rating Parameter Symbol Condition min SM5006AKAS, CF5006AKA SM5006AKBS, CF5006AKB SM5006AKCS, CF5006AKC SM5006CKDS, CF5006CKD SM5006DKCS, CF5006DKC SM5006AKDS, CF5006AKD SM5006BKCS, CF5006BKC LOW-level output voltage Output leakage current HIGH-level input voltage LOW-level input voltage VOL IZ VIH VIL Q: Measurement cct 2, VDD = 4.5V, IOL = 16mA Q: Measurement cct 2, INHN = LOW, VDD = 5.5V INHN INHN f = 30MHz f = 40MHz f = 60MHz, Ta = -15 to 75C f = 60MHz, Ta = 0 to 70C f = 70MHz, Ta = -20 to 80C f = 70MHz, Ta = -15 to 75C f = 70MHz, Ta = 0 to 70C INHN pull-up resistance RUP Measurement cct 4 SM5006AKAS, CF5006AKA SM5006AKBS, CF5006AKB Feedback resistance Rf Measurement cct 5 SM5006AKCS, CF5006AKC SM5006AKDS, CF5006AKD SM5006CKDS, CF5006CKD Built-in resistance RG RD Built-in capacitance CG CD Design value, determined by the Rf value Design value, determined by the Rf value Design value. A monitor pattern on a wafer is tested. Design value. A monitor pattern on a wafer is tested. SM5006AKAS CF5006AKA SM5006AKBS CF5006AKB CF5006AKC CF5006DKC SM5006AKCS SM5006DKCS CF5006AKD CF5006BKC CF5006CKD SM5006AKDS SM5006BKCS SM5006CKDS VOH = VDD VOL = VSS typ max Unit
HIGH-level output voltage
VOH
Q: Measurement cct 1, VDD = 4.5V, IOH = 16mA
3.9
4.2
- V
4.0 - - - 2.0 - - - - - - -
4.2 0.3 - - - - 16 18 25 25 35 35
- 0.4 10 A 10 - 0.8 32 36 50 50 70 70 V V V
Current consumption
IDD
INHN = open, Measurement cct 3, load cct 1, VDD = 4.5 to 5.5V, CL = 15pF
mA
- 50 6.97 4.76 4.16 2.21 17 17 7.44 14.88
35 - 8.2 5.6 4.9 2.6 20 20 8 16
70 150 9.43 6.44 5.64 2.99 23 23 8.56 pF 17.12 k k
SEIKO NPC CORPORATION --9
SM5006 series 5006AH series VDD = 4.5 to 5.5V, VSS = 0V, Ta = -40 to 85C unless otherwise noted.
Rating Parameter HIGH-level output voltage LOW-level output voltage Output leakage current HIGH-level input voltage LOW-level input voltage Symbol VOH VOL IZ VIH VIL Condition min Q: Measurement cct 1, VDD = 4.5V, IOH = 4mA Q: Measurement cct 2, VDD = 4.5V, IOL = 4mA Q: Measurement cct 2, INHN = LOW, VDD = 5.5V INHN INHN f = 30MHz f = 40MHz INHN = open, Measurement cct 3, load cct 1, VDD = 4.5 to 5.5V, CL = 15pF f = 60MHz, Ta = -20 to 80C f = 60MHz, Ta = -15 to 75C f = 70MHz, Ta = -20 to 80C f = 70MHz, Ta = -15 to 75C INHN pull-up resistance RUP Measurement cct 4 SM5006AHAS, CF5006AHA SM5006AHBS, CF5006AHB Feedback resistance Rf Measurement cct 5 SM5006AHCS, CF5006AHC SM5006AHDS, CF5006AHD Built-in resistance RG RD Built-in capacitance CG CD Design value, determined by the Rf value Design value, determined by the Rf value Design value. A monitor pattern on a wafer is tested. Design value. A monitor pattern on a wafer is tested. 4.16 2.21 17 17 7.44 14.88 4.9 2.6 20 20 8 16 5.64 2.99 23 23 8.56 pF 17.12 SM5006AHAS CF5006AHA SM5006AHBS CF5006AHB CF5006AHC SM5006AHCS CF5006AHD SM5006AHDS VOH = VDD VOL = VSS 3.9 - - - 2.0 - - - - - - - 50 6.97 4.76 typ 4.2 0.3 - - - - 15 18 25 25 32 32 - 8.2 5.6 max - 0.5 10 A 10 - 0.8 30 36 50 mA 50 65 65 150 9.43 6.44 k k V V V V Unit
Current consumption
IDD
SEIKO NPC CORPORATION --10
SM5006 series
Switching Characteristics
5006xN series 3V operation: VDD = 2.7 to 3.6V, VSS = 0V, Ta = -20 to 80C unless otherwise noted.
Parameter Symbol Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD , CL = 15pF, Ta = -10 to 70C Condition SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNCS, CF5006BNC SM5006BNES, CF5006BNE SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNCS, CF5006BNC SM5006BNES, CF5006BNE SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006ANCS, CF5006ANC SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC Rating min typ max Unit
tr1
-
3.5
7.0
Output rise time tr2 Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD , CL = 15pF
ns - 3.5 7.0
tf1
Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD , CL = 15pF, Ta = -10 to 70C
-
3.5
7.0
Output fall time tf2 Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD , CL = 15pF
ns - 3.5 7.0
Measurement cct 3, load cct 1, Ta = 25C, VDD = 3.3V, CL = 15pF, f = 30MHz Measurement cct 3, load cct 1, Ta = 25C, VDD = 3.3V, CL = 15pF, f = 40MHz Output duty cycle*1 Duty Measurement cct 3, load cct 1, Ta = 25C, VDD = 3.3V, CL = 15pF, f = 50MHz Measurement cct 3, load cct 1, Ta = 25C, VDD = 3.3V, CL = 15pF, f = 70MHz Output disable delay time Output enable delay time tPLZ tPZL
40
-
60
40
-
60 %
SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNES, CF5006BNE SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE
40
-
60
40
-
60
Measurement cct 3, load cct 1, Ta = 25C, VDD = 5V, CL 15pF
- -
- -
100 100
ns ns
*1. The duty cycle characteristic is checked the sample chips of each production lot.
SEIKO NPC CORPORATION --11
SM5006 series 5V operation: VDD = 4.5 to 5.5V, VSS = 0V, Ta = -40 to 85C unless otherwise noted.
Parameter Symbol Condition SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE CF5006ANE CF5006ANF CF5006BNE SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC tr3 Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD , CL = 50pF SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNES, CF5006BNE SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE CF5006ANE CF5006ANF CF5006BNE SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC tf3 Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD , CL = 50pF SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNES, CF5006BNE Rating min typ max Unit
-
2.0
4.0
tr1
Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD , CL = 15pF
-
1.5
3.0
tr2 Output rise time
Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD , CL = 30pF
-
2.0
4.0 ns
-
4.0
8.0
-
3.5
7.0
-
3.0
6.0
-
2.0
4.0
tf1
Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD , CL = 15pF
-
1.5
3.0
tf2 Output fall time
Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD , CL = 30pF
-
2.0
4.0 ns
-
4.0
8.0
-
3.5
7.0
-
3.0
6.0
SEIKO NPC CORPORATION --12
SM5006 series
Rating min SM5006ANAS CF5006ANA SM5006ANBS CF5006ANB SM5006ANCS CF5006ANC SM5006ANDS CF5006AND SM5006BNCS CF5006BNC CF5006ANE SM5006ANES CF5006ANF CF5006BNE SM5006ANFS SM5006BNES SM5006CNCS CF5006CNC SM5006DNCS CF5006DNC SM5006CNES CF5006CNE SM5006DNES CF5006DNE SM5006CNCS CF5006CNC SM5006CNDS CF5006CND SM5006DNCS CF5006DNC 45 45 45 typ - - - max 55 55 55
Parameter
Symbol
Condition f = 30MHz, CL = 50pF f = 40MHz, CL = 50pF f = 60MHz, CL = 50pF f = 70MHz, CL = 50pF f = 100MHz, CL = 30pF f = 100MHz, CL = 15pF
Unit
45
-
55
45 45 45 45
- - - -
55 55 55 55
Output duty cycle*1
Duty
Measurement cct 3, load cct 1, Ta = 25C, VDD = 5.0V
f = 107MHz, CL = 30pF f = 107MHz, CL = 15pF f = 50MHz, CL = 50pF
%
45
-
55
f = 100MHz, CL = 15pF f = 60MHz, CL = 15pF f = 70MHz, CL = 15pF Output disable delay time Output enable delay time tPLZ tPZL
45
-
55
40
-
60
40
-
60
Measurement cct 3, load cct 1, Ta = 25C, VDD = 5V, CL 15pF
- -
- -
100 100
ns ns
*1. The duty cycle characteristic is checked the sample chips of each production lot.
SEIKO NPC CORPORATION --13
SM5006 series 5006xK series VSS = 0V, Ta = -40 to 85C unless otherwise noted.
Parameter Symbol Condition Measurement cct 3, load cct 1, 0.4V to 2.4V, VDD = 4.5 to 5.5V Measurement cct 3, load cct 1, 2.4V to 0.4V, VDD = 4.5 to 5.5V f = 30MHz f = 40MHz f = 60MHz Output duty cycle*1 Measurement cct 3, load cct 1, Ta = 25C, VDD = 5.0V, CL = 15pF CL = 15pF CL = 50pF CL = 15pF CL = 50pF SM5006AKAS CF5006AKA SM5006AKBS CF5006AKB SM5006AKCS CF5006AKC SM5006AKDS CF5006AKD SM5006BKCS CF5006BKC SM5006DKCS CF5006DKC SM5006CKDS CF5006CKD SM5006DKCS CF5006DKC Rating min - - - - 45 45 40 typ 2 - 2 - - - - max 4 7 4 7 55 55 60 Unit
Output rise time
tr tf
ns
Output fall time
ns
Duty
f = 70MHz
45
-
55
%
f = 50MHz
45
-
55
f = 70MHz Output disable delay time Output enable delay time tPLZ tPZL
40
-
60
Measurement cct 3, load cct 1, Ta = 25C, VDD = 5V, CL 15pF
- -
- -
100 100
ns ns
*1. The duty cycle characteristic is checked the sample chips of each production lot.
5006AH series VDD = 4.5 to 5.5V, VSS = 0V, Ta = -40 to 85C unless otherwise noted.
Parameter Symbol tr1 tr2 tf1 tf2 Condition Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD f = 30MHz f = 40MHz f = 50MHz Output duty cycle*1 Duty Measurement cct 3, load cct 1, Ta = 25C, VDD = 5.0V, CL = 15pF f = 60MHz, Ta = -20 to 80C f = 60MHz, Ta = -15 to 75C f = 70MHz, Ta = -20 to 80C f = 70MHz, Ta = -15 to 75C Output disable delay time Output enable delay time tPLZ tPZL CL = 15pF CL = 50pF CL = 15pF CL = 50pF SM5006AHAS CF5006AHA SM5006AHBS CF5006AHB SM5006AHCS CF5006AHC CF5006AHC SM5006AHCS CF5006AHD SM5006AHDS Rating min - - - - 45 45 45 40 40 40 40 - - typ 5.0 13 5.0 13 - - - - - - - - - max 7.0 21 7.0 21 55 55 55 60 60 60 60 100 100 ns ns % Unit
Output rise time
ns
Output fall time
ns
Measurement cct 3, load cct 1, Ta = 25C, VDD = 5V, CL 15pF
*1. The duty cycle characteristic is checked the sample chips of each production lot.
SEIKO NPC CORPORATION --14
SM5006 series
Current consumption and Output waveform with NPC's standard crystal
f [MHz]
R [] 18.62 20.53 22.17 25.42 16.60 35.83
L [mH] 16.24 11.34 7.40 4.18 3.56 2.98
Ca [fF] 1.733 1.396 1.370 1.254 0.726 0.732
Cb [pF] 5.337 3.989 4.105 5.170 5.394 2.265
Cb
30 40 50 70 100 107
L
Ca
R
FUNCTIONAL DESCRIPTION
Standby Function
When INHN goes LOW, the oscillator output on Q goes high impedance.
INHN HIGH (or open) LOW Q fO output frequency High impedance Oscillator Normal operation Normal operation
SEIKO NPC CORPORATION --15
SM5006 series
MEASUREMENT CIRCUITS
Measurement cct 1 Measurement cct 4
VDD
5.0V
Q R2
Signal Generator
R1
C1 XT Rfo XTN VSS
VDD RUP = VSS INHN VDD IPR
Q out monitor
VOH 0V
VIH A
IPR
3.5VP-P , 10MHz sine wave input signal (5V operation) 2.0VP-P , 10MHz sine wave input signal (3V operation) C1 : 0.001F R1 : 50 R2 : 250 (5006xNx/5V operation) 275 (5006xNx/3V operation) 245 (5006AKA, AKB, AKC, CKD, DKC) 250 (5006AKD, BKC) 975 (5006AHx) Rfo : 2.7k (5006Bxx, Dxx)
Measurement cct 2
Measurement cct 5
IOL, IZ VDD XT INHN VSS Q IZ XT VDD
A
XTN
Rf = VSS
VDD IRf
V VOL A
IRf
Measurement cct 3
A
XT Rfo X'tal XTN INHN VDD
IDD IST
Q VSS
Rfo : 2.7k (5006Bxx, Dxx)
SEIKO NPC CORPORATION --16
SM5006 series
Load cct 1
Load cct 2
Q output CL
(Including probe capacitance)
400 Q output CL
(Including probe capacitance)
Switching Time Measurement Waveform
Output duty level (CMOS)
Q output
0.9VDD 0.1VDD TW
0.9VDD 0.1VDD
DUTY measurement voltage (0.5V DD)
tr
Output duty level (TTL)
tf
Q output
2.4VDD 0.4VDD TW
2.4VDD 0.4VDD
DUTY measurement voltage (1.4V DD)
tr
Output duty cycle (CMOS)
tf
Q output
TW T
DUTY measurement voltage (0.5VDD) DUTY= TW/ T 100 (%)
Output duty cycle (TTL)
Q output
TW T
DUTY measurement voltage (1.4VDD) DUTY= TW/ T 100 (%)
SEIKO NPC CORPORATION --17
SM5006 series
Output Enable/Disable Delay
INHN
VIH VIL
tPLZ Q output
INHN input waveform
tPZL
tr = tf
10ns
SEIKO NPC CORPORATION --18
SM5006 series
Please pay your attention to the following points at time of using the products shown in this document. The products shown in this document (hereinafter "Products") are not intended to be used for the apparatus that exerts harmful influence on human lives due to the defects, failure or malfunction of the Products. Customers are requested to obtain prior written agreement for such use from SEIKO NPC CORPORATION (hereinafter "NPC"). Customers shall be solely responsible for, and indemnify and hold NPC free and harmless from, any and all claims, damages, losses, expenses or lawsuits, due to such use without such agreement. NPC reserves the right to change the specifications of the Products in order to improve the characteristic or reliability thereof. NPC makes no claim or warranty that the contents described in this document dose not infringe any intellectual property right or other similar right owned by third parties. Therefore, NPC shall not be responsible for such problems, even if the use is in accordance with the descriptions provided in this document. Any descriptions including applications, circuits, and the parameters of the Products in this document are for reference to use the Products, and shall not be guaranteed free from defect, inapplicability to the design for the mass-production products without further testing or modification. Customers are requested not to export or re-export, directly or indirectly, the Products to any country or any entity not in compliance with or in violation of the national export administration laws, treaties, orders and regulations. Customers are requested appropriately take steps to obtain required permissions or approvals from appropriate government agencies.
SEIKO NPC CORPORATION
15-6, Nihombashi-kabutocho, Chuo-ku, Tokyo 103-0026, Japan Telephone: +81-3-6667-6601 Facsimile: +81-3-6667-6611 http://www.npc.co.jp/ Email: sales@npc.co.jp
NC9713FE 2006.04
SEIKO NPC CORPORATION --19

▲Up To Search▲

Price & Availability of SM500606

	To Download SM500606 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .